Cylinder Screen Printing
Machine Cylindrical Silk Screen Printing Press for Mugs Pen Cup Bottle 6
Inches Diameter Screen Press for DIY Curved screen printing machine
is mainly used for printing cylindrical type, cone type products; Such
as a variety of plastic, glass, metal materials made of cylindrical,
conical shape products, including wine bottles, medicine bottles,
cosmetics bottles and other packaging bottles; Mugs, thermos mugs, beer
mugs, red mugs, etc. Glass tube, pen ,ballpoint pen, fishing rod, bat
and other small cylindrical products; Pure bucket, paint bucket, alcohol
bucket, paint bucket, oil and lubricating oil bucket and other large
packaging cylindrical products. For
cylindrical or conical type products, the printing surface has a large
concave or convex, the printing surface has spots and other non-plane
printing is not suitable for the machine. Note! This curved
screen printing machine is mainly used for printing cylindrical and
conical products with a diameter below 150 mm. The maximum
printing height of the machine is 270 mm, the length of the arc is 380
mm. Introduction: This machine adopts the printing screen frame
height positioning structure, the front part is equipped with the
parallel placement plate, the whole machine is firm and stable in the
printing process. Printing materials and tools such as ink buckets can
be placed on the rear horizontal board of the main machine. The printing plate
frame uses the spring to pull and lift, matches the flower basket screw
to adjust the lift strength of the screen plate , the lift angle of the
screen plate can be controlled by adjusting knob, the operation is
easier. The spring tension on both sides of the machine should be as
consistent as possible after installation , otherwise it may cause
distortion of the printing screen frame. It is easy to install and remove the screen
frame. Just put the screen plate into the back support plate from below
of the printing plate rack, and then put the screen plate into the front
support plate, tighten the screen plate fixing screw. (limited to the
design requirements of the machine, the screen board of the machine must
use the screen frame with the outer diameter of 560*410 mm and the
height within 30 mm.) 2 screen frames are attached to the machine. 1.Place the screen frame into the rear support
plate from the bottom of the installation table. 2.Move the front of the frame to the front support plate, tighten four
Screws to fix the screen frame. 6 sliders connected to the optical axis to make
the screen frame slide back and forth,it is easy and smooth to push and
pull. The back and forth sliding distance of the frame
can be controlled by the positioning ring on the optical axis; The user
can lock the positioning ring after adjusting the position of the screen
plate and the substrate placement table. Especially add the collision
rubber ring between the locating ring and the slide block, which can
prevent the slide block from directly contacting with the metal locating
ring during the back and forth sliding of the screen frame, and prevent
the sound of metal striking with each other, and meanwhile protect the
metal parts. The printing scraper rack and the return ink
rack adopt the double board clip type, the installation and unloading is
convenient and quick, two sides of the main frame and the frame connect
the screw middle additional spring, in the printing process, user can
adjust the printing scraper and the return ink plate pressure according
to the need. Substrate placement platform adopts knob lifting
and locking structure. Substrate placement platform can be controlled by
the lifting handle under the placement stage, first release the knob on
both sides of the baffle, lift to the appropriate height, the locking
knob on both sides of the baffle can be tightened to stabilize the
lifting platform at this height, substrate placement platform on both
sides of the height is consistent or not can be adjusted by the concave
teeth on both sides of the baffle. Bottom of the substrate printing rack is
designed around back and forth mobile , the three long aluminum bars in
the bottom installed in the lifting placement platform, both sides are
substrate placement rack installation bar, the middle is the substrate
limit column installation bar. Substrate placement rack installation bar can be moved around 140 mm
back and forth, in order to move as accurate as possible, according to
the concave tooth on the placement table to make parallel movement. Limited post is installed on both sides of the
substrates limited post installation bar, after adjusting all printing
steps, place the substrate in the printing rack, move two limited posts
respectively to the two ends of the substrates and substrates surface
with 1-2 mm spacing (Note: not too close please , otherwise it may
affect the rotation of the substrates), using a wrench to tighten the
limited post. Operations: 1.Open the scraper mounting plate. 2.Put in the scraper rubber, the lower edge of the
scraper and the mesh surface will fit smoothly and smoothly. 3.Fix the following three screws (don't tighten
them); tighten the top two white knobs to fix the scraper tape. Push and pull handle can be installed vertically or in parallel
according to the operator's needs Main Functions of
the Limited Post: 1.Improve the accuracy of substrate placement,
ensure that all printing positions are basically the same after
substrate placement, and avoid deviation of printing positions caused by
different substrate placement. 2.Substrate
placement faster, no need to mark or manually adjust, directly put into
the substrate. 3.Limit the substrate in the printing process
does not deviate. There are two sets substrate placement wheels,
one set is diameter of 50 mm blue rotation wheel, the other set is
diameter of 26 mm white rotation wheel, two sets rotation wheel can be
installed in the placement of the main frame and additional frame, users
can replace according to the needs of adjustment. The attached plate configured by the machine is
used in conjunction with the substrate placement in the main frame,
which is mainly used for printing products with conical shape. The
attached plate can be connected with the main frame vertically with two
screws, or cross connected with the italic body of the main frame with
one screw. The machine has been fully adjusted before
leaving the factory. The customer only needs to install the spring and
screen frame landing board for use. The main body of the machine uses advanced electrostatic spraying metal
surface treatment, acid and alkali resistance, corrosion resistance,
clean resistance, no rust, can be used for a long time; Some parts are
made of stainless steel and aluminum alloy. Equipped with a full set of installation tools and detailed installation
instructions; Easy installation without additional tools. Export to Europe and America standard fumigation-free wooden box
packaging, all kinds of metal parts in the box are individually packaged
or placed in isolation to ensure that all kinds of metal parts do not
contact directly. Details:
Item Included: 1 PC Cylinder Screen Printing Machine
Cylindrical Silk Screen Printing Press for Mugs Pen Cup Bottle 006596
Shipping & Handling Details Default Shipping Cost or
Free Shipping Information:
▲ Default shipping
cost or free shipping service is
only for the customers from Canada
or the lower 48 United States
by Canada Post, USPS or the UPS
Ground.Customers from other areas
or needs other shipping ways,
please contact us. ▲ Buyers from
Guam,Puerto Rico, Virgin Islands,
American Samoa,Alaska,Hawaii,PO
Boxes, APO/FPO addresses or
other countries/areas, there WILL
be extra shipping costs, please
contact us for more
detailed information. ▲ Please make
sure your address is valid for both
UPS and USPS services. Any costs
incurred because of incorrect
or undeliverable address should be
undertaken by buyer. Handling Time: Shipping is
usually made in 1-3 business days
after payments cleared. Orders are
processed from Monday-Friday; Not
on the weekends &
public holidays. Sales tax/Customs duties: Any sales
taxes or Customs duties are not
included. If came out, they must
be undertaken by the buyer. Damage In Shipping: Email or
call us First! We will work with you
to get the case resolved in the
fastest method.
Return / Refund If you are not 100%
happy with your purchase, please
contact Us. Please don't directly
opened a request or case without
informing us, or else, we will do
some discounts on the warranty and
other sales-services later on.
Hope for your understanding. Returns &
Exchanges ▲ All returns
must be made within 14 days of
delivery date. Items must be in
new, unused condition, with all
original materials included with
the shipment. A partial refund
may be applied for opened or
damaged items, depending on
the condition. ▲ Items returned
under the buyer's remorse: The
return shipping fee must be
covered by the buyer;The original
shipping cost will also be
deducted from the refund. 15%
restocking fee of the items
purchase price will be charged. ▲ Returns that
are the result of our seller's
error: Buyer will receive a full
refund of the item as well as
shipping charges ▲ All
returns require a RA (Return
Authorization) number that will
be given by our seller. Please
contact with us at first for
more details. Defective &
Damaged Products ▲ If product
was received damaged or not as
described, please send us some
pictures or videos, so we could
well understand your problem, then
solve them for you ASAP. Besides,
it's much helpful for us to claim
with UPS,remind our related
department to pay much more
attention to packaging later on.
Hope for your understanding. ▲ Replacement or
refund of defective or damaged
products can only be returned in
exchange for the exact same
product,or else,the purchase price
will be refunded back to your
original payment method. ▲ If an
item is received damaged,customer
service must be contacted within 7
days of receiving your item.
All returns require a RA (Return
Authorization) number as above.
Warranty & Feedback ▲ 6 months'
warranty for the machines, not for
the consumables.We stand behind our
products all the item, so even if
your warranty period has expired,
you can still seek for service or
technical support from us with low
cost. ▲ Any warranty
shipping cost to us is responsible
by buyer. ▲ Any shipping
cost to buyer is responsible by the
seller. ▲ We committee
to the customer satisfaction and
want to bring you the best
purchase experience. If there is
any problems,please contact us
ASAP. If not,please leave us a
positive feedback as it's very
important for us. Thanks very much.
Returns Accepted for this item if it's within 30 Days